qpl9097 ultra low - noise, bypass lna d ata sheet august 2 5 , 201 7 | subject to change without notice 1 of 9 www.qorvo.com 8 pin 2x2 mm dfn p ackage general description the qpl9097 is a high - linearity, ultra - low noise gain block amplifier with a bypass mode functionality integrated in the product. at 3.8 ? ghz, the amplifier typically provides 2 2 db gain, +3 2 dbm oip3, and 1. 0 db noise figure while drawing 5 0 ma current from a + 4.2 ? v supply. the qpl9097 is internally matched using a high performance e - phemt process and only requires four external components for operation from a single positive supply: an external rf choke and blocking/bypass capacitors. this low noise amplifier contains an internal active bias to maintain high performance over temperature. the qpl9097 is optimized for the 3. 3 ? C ? 4.2 ghz frequency band and is targeted for wireless infrastruc ture. the qpl90 97 is packaged in a 2?x?2?mm dfn. applications ? base - station receivers ? repeaters / das ? tower mounted amplifiers ? mobile infrastructure ? general purpose wireless ? tdd or fdd systems product features ? 3. 3 C 4.2 ghz operational bandwidth ? lna with integrate d bypass mode ? ability to turn lna and bypass mode off ? ultra low noise, 1. 0 db at 3.8 ?ghz ? 2 2 db gain at 3.8 ?ghz ? +3 2 dbm output ip3 in lna mode ? + 35 dbm input ip3 in bypass mode ? internally matched ? positive supply only, +3.3 to +5?v ? 2x2 mm 8 - pin dfn plastic p ackage functional block diagram top view ordering information part no. description qpl9097 sr 100 pcs on 7 reel qpl9097 tr7 2500 pcs on 7 reel qpl9097 evb p 01 (1) evaluation board 1. refer board details and performance on pgs. 3 & 4. ? b a c k s i d e p a d d l e - r f / d c g n d p i n 1 r e f e r e n c e m a r k 8 7 6 5 1 2 3 4 v d d r f o u t g n d v s d g n d r f i n n / c v b y p
qpl9097 ultra low - noise, bypass lna d ata sheet august 2 5 , 201 7 | subject to change without notice 2 of 9 www.qorvo.com absolute ma ximum ratings parameter rating storage temperature ?6 5 to 150c supply voltage (v dd ) + 7 v rf input power, cw, 50, t=25 c +30 dbm operation of this device outside the parameter ranges given above may cause permanent damage. recommended operating conditions parameter min typ max units supply voltag e (v dd ) 3. 0 4.2 5.25 v t case ? 40 + 105 c t j at t case = 125 c + 14 2 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all recommended operating conditions. electrical specifications te st conditions unless otherwise noted: v dd = +4.2 v, temp.=+ 25 c . parameter conditions min typ max units operational frequency range 3 3 00 42 00 mhz test frequency 42 00 mhz gain lna on, bypass off 2 2 db input return loss lna on, bypass off 1 2 db output return loss lna on, bypass off 11 .5 db noise figure (2) lna on, bypass off 1. 1 db output p1db lna on, bypass off + 1 5.5 dbm output ip3 lna on, bypass off, pout=+0 dbm/tone, f= 5 mhz +32 .5 dbm insertion loss lna off, bypass on 2.0 db return loss lna off, bypass on 1 3 db isolation (1) lna off, bypass off 20 db output ip3 lna off, bypass on pin=+3 dbm/tone, f= 5 mhz + 35 dbm control voltage, v 1 , v 2 v ih 1 .17 v dd v v il 0 0. 63 v current, i d bypass off 5 0 ma bypass on 5 ma switching speed lna - bypass (50% vctrl to 10% rf) 137 ns bypass - lna(50% vctrl to 90% rf) 354 ns lna - off(50% vctrl to 10% rf) 26 ns off - lna(50% vctrl to 90% rf) 55 n s thermal resistance, jc channel to case 44 c/w 1. minimum specification listed is guaranteed by design. not tested in production. 2. input trace loss de - embedded from noise figure data. control truth table v byp v sd state 0 0 lna on, bypass off 0 1 lna off, bypass off 1 x lna off, bypass on ?
qpl9097 ultra low - noise, bypass lna d ata sheet august 2 5 , 201 7 | subject to change without notice 3 of 9 www.qorvo.com qpl9097 evaluation board notes: 1. a through line is included on the evaluation board to de - embed the board losses. 2. c14 and l2 are placed as close to device as possible. any trace length between the device a nd components will add parasitics that will affect the tune. bill of material C qpl9097 evaluation board reference des. value description manuf. part number n/a n/a printed circuit board qorvo u1 n/a ultra low noise, bypass lna qorvo qpl9097 c11,c 12 20k ohm res, 0402, 1%, 1/10w various r1, r3,r4, c4 0 ? res, 0402, +/ - 5%, 1/16w murata c1,5,8 18 pf cap, 0402, +/ - 5%, 50v murata c10 1000pf cap, 0402, 10%, 50v, x7r various c9 1.0uf cap, 0402, 10%, 10v, x5r various c14 1.2 pf cap, 0402, 0.1pf, 50v, c0g murata gjm1555c1h1r2bb01d l2 2.4 nh ind, 0402, 5%, ww coilcraft 0402cs - 2n4xjlw r5 75k res, 0402, 5% ? l 1 c 1 0 c 9 r 3 u 1 c 8 c 5 c 4 r 4 r 1 c 1 c 1 1 c 1 2 r 5 c 1 4 l 2 j 2 r f o u t p u t j 8 g n d j 3 v d d j 1 r f i n p u t l 1 1 8 n h ( 0 6 0 3 ) c 4 1 8 p f c 1 1 8 p f c 1 0 1 u f c 9 1 0 0 0 p f r 3 0 ? 8 7 6 5 1 2 3 4 j 5 v 1 j 4 v 2 r 4 0 ? r 1 0 ? u 1 c 1 2 2 0 k c 1 1 2 0 k l 2 2 . 4 n h c 1 4 1 . 2 p f r 5 7 5 k
qpl9097 ultra low - noise, bypass lna d ata sheet august 2 5 , 201 7 | subject to change without notice 4 of 9 www.qorvo.com typical performance (lna mode) test conditions unless otherwise noted: v dd = + 4.2 v, v 1 = 0. 63 v, v 2 = 0.63 v, i d = 50 ma, temp.=+25 ? c . param eter typical value units frequency 3.4 3.6 3.8 4.0 m hz gain 24 23 22 20 db noise figure 0.9 1.0 1.1 1.2 db input return loss 14 12.5 12 11 db output return loss 11 11 1 1.5 12 db o ip3 (pout/tone=+ 0 dbm, f = 1 mhz) 32.5 32.6 32 .2 32.2 dbm p1db 15 .5 15.6 15.5 15.4 dbm typical performance (bypass mode) test conditions unless otherwise noted: v dd = + 4.2 v, v 1 = 1.17v , v 2 = 1. 17 v or 0.63v , i d = 5 ma, temp.=+25 ? c . parameter typical value units frequency 3.4 3.6 3.8 4.0 m hz insertion loss 2.2 2.0 2 .0 2.0 db input return loss 13.5 13 12.5 12 db output return loss 14 16.5 17.5 17 db input ip3 (p in /tone=+ 3 dbm, f = 1 mhz) 39.2 38.2 38 38 dbm typical performance (lna off, bypass off mode) test conditions unless otherwise noted: v dd = + 4.2 v, v 1 = 0.63 v, v 2 = 1.17 v, temp. = +25 ? c . parameter typical value units frequency 3.4 3.6 3.8 4.0 m hz isolation 16.5 18 20 22 db ?
qpl9097 ultra low - noise, bypass lna d ata sheet august 2 5 , 201 7 | subject to change without notice 5 of 9 www.qorvo.com performance plots test conditions unless otherwise noted: v dd = +4.2 v ? 10 15 20 25 30 3000 3400 3800 4200 4600 5000 gain (db) frequency (mhz) gain vs. frequency (lna mode) +95? c +25? c ?40? c -20 -15 -10 -5 0 3000 3400 3800 4200 4600 5000 |s11| (db) frequency (mhz) input return loss vs. frequency (lna mode) +95? c +25? c ?40? c -20 -15 -10 -5 0 3000 3400 3800 4200 4600 5000 |s22| (db) frequency (mhz) output return loss vs. frequency (lna mode) +95? c +25? c ?40? c -5 -4 -3 -2 -1 0 3000 3400 3800 4200 4600 5000 gain (db) frequency (mhz) gain vs. frequency (bypass mode) +95? c +25? c ?40? c -20 -15 -10 -5 0 3000 3400 3800 4200 4600 5000 |s11| (db) frequency (mhz) input return loss vs. frequency (bypass mode) +95? c +25? c ?40? c -20 -15 -10 -5 0 3000 3400 3800 4200 4600 5000 |s22| (db) frequency (mhz) output return loss vs. frequency (bypass mode) +95? c +25? c ?40? c -30 -25 -20 -15 -10 -5 0 3000 3400 3800 4200 4600 5000 isolation (db) frequency (mhz) isolation vs. frequency (off mode) +95? c +25? c ?40? c -5 -4 -3 -2 -1 0 3000 3400 3800 4200 4600 5000 |s11| (db) frequency (mhz) input return loss vs. frequency (off mode) +95? c +25? c ?40? c -10 -8 -6 -4 -2 0 3000 3400 3800 4200 4600 5000 |s22| (db) frequency (mhz) output return loss vs. frequency (off mode) +95? c +25? c ?40? c 27 28 29 30 31 32 33 34 35 36 37 -3 -2 -1 0 1 2 3 4 5 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone (lna mode) +95? c +25? c ?40? c frequency = 3.8 ghz 29 30 31 32 33 34 -3 -2 -1 0 1 2 3 4 5 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone (lna mode) 3.3 ghz 3.4 ghz 3.6 ghz 3.8 ghz 4.0 ghz 4.2 ghz temp.=+25? c 12 13 14 15 16 17 18 3400 3500 3600 3700 3800 3900 4000 4100 4200 p1db (dbm) frequency (mhz) p1db vs frequency (lna mode) +95? c +25? c ?40? c
qpl9097 ultra low - noise, bypass lna d ata sheet august 2 5 , 201 7 | subject to change without notice 6 of 9 www.qorvo.com perf ormance plots contd. test conditions unless otherwise noted: v dd = +4.2 v ? 30 31 32 33 34 35 36 37 38 39 40 -1 0 1 2 3 4 5 6 7 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone (bypass mode) +95? c +25? c ?40? c frequency = 3.8 ghz 30 31 32 33 34 35 36 37 38 39 40 -1 0 1 2 3 4 5 6 7 oip3 (dbm) pout/tone (dbm) oip3 vs pout/tone (bypass mode) 3.3 ghz 3.4 ghz 3.6 ghz 3.8 ghz 4.0 ghz 4.2 ghz temp.=+25? c 20 21 22 23 24 25 26 27 3400 3500 3600 3700 3800 3900 4000 4100 4200 p1db (dbm) frequency (mhz) p1db vs frequency (bypass mode) +95? c +25? c ?40? c 0.0 0.5 1.0 1.5 2.0 2.5 3.0 2 2.5 3 3.5 4 4.5 5 5.5 6 noise figure (db) frequency (ghz) noise figure vs frequency +95? c +25? c ?40? c
qpl9097 ultra low - noise, bypass lna d ata sheet august 2 5 , 201 7 | subject to change without notice 7 of 9 www.qorvo.com evaluation board pcb information qorvo pcb 28 4701 material and stack - up 50 ohm line dimensions: width = 0.0 182 , spacing = 0.0 20 pin configuration and des cription pin no. label description 1, 6 gnd rf/dc ground pin. 2 rfin rf input pin. dc block required. 3 n /c no internal connection. provide grounded pcb land pads for mounting integrity. 4 v byp control pin for bypass mode . the lna is automatically turned off when the bypass mode is activated. refer to truth table on pg 2. 5 v sd control pin to disable the lna. refer to truth table on pg. 2. 7 rfout rf output pin. dc block required. 8 v dd supply voltage pin. external chok e and bypass capacitors needed. backside paddle rf/dc gnd rf/dc ground. follow recommended via pattern and ensure good solder attach for best thermal and electrical performance. ? b a c k s i d e p a d d l e - r f / d c g n d p i n 1 r e f e r e n c e m a r k 8 7 6 5 1 2 3 4 v d d r f o u t g n d v s d g n d r f i n n / c v b y p r o g e r s 4 0 0 3 c r = 3 . 5 t y p . 1 o z . c u b o t t o m l a y e r f r 4 f r 4 1 o z . c u t o p l a y e r 1 o z . c u i n n e r l a y e r 1 o z . c u i n n e r l a y e r 0 . 0 6 2 " 0 . 0 0 6 " f i n i s h e d b o a r d t h i c k n e s s 0 . 0 0 8 " 0 . 0 0 8 "
qpl9097 ultra low - noise, bypass lna d ata sheet august 2 5 , 201 7 | subject to change without notice 8 of 9 www.qorvo.com mechanical information package marking and dimensions n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. except where noted, this part outline conforms to jedec standard mo - 220, issue e (variation vggc) for thermally enhanced plastic very thin fine pitch quad flat no lead package (qfn). 3. dimension and tole rance formats conform to asme y14.4m - 1994. 4. the terminal #1 identifier and terminal numbering conform to jesd 95 - 1 spp - 012. pcb mounting pattern n otes : 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. vias are required under the backside paddle of this device for proper rf/dc grounding and thermal dissipation. we recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10) . 4. ensure good package backside paddle solder attach for reliable operation and best electrical performance. 9 097 trace code ?
qpl9097 ultra low - noise, bypass lna d ata sheet august 2 5 , 201 7 | subject to change without notice 9 of 9 www.qorvo.com rohs compliance this part is compliant with 2011/65/eu rohs directive (restrictions on the use of certain hazardous substances in electrica l and electronic equipment) as amended by directive 2015/863/eu. this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free handling precautions paramete r rating standard caution! esd - sensitive device esd? C ?human body model (hbm) class 1b esda?/?jedec js - 00 1 - 20 14 esd? C ?charged device model ( cd m) class c3 esda / jedec js - 002 - 2014 msl? C ?moisture sensitivity level level 1 ipc/jedec j - std - 020 sol derability compatible with lead - free (260c max. reflow temp.) soldering process. solder profiles available upon request. contact plating: nipdau important notice the information contained herein is believed to be reliable; however, qorvo makes no warranties regarding the information contained herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. all information contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for qorvo products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual p roperty rights, whether with regard to such information itself or anything described by such information. this information does not constitute a warranty with respect to the products described herein, and qorvo hereby disclaims any and all warranties with respect to such products whether express or implied by law, course of dealing, course of performance, usage of trade or otherwise, including the implied warranties of merchantability and fitness for a particular purpose. without limiting the generality of the foregoing, qorvo products are not warranted or authorized for use as critical components in medical, life - saving, or life - sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or de ath. copyright 201 7 ? qorvo, inc. | qorvo is a registered trademark of qorvo, inc. contact information for the latest specifications, additional product information, worldwide sales and distribution locations : web: www.qorvo.com tel: 1 - 844 - 890 - 8163 email: customer.support@qorvo.com for technical questions and application information: email: appsupport@qorvo.com p b ?
|
